Chinese  Service hotline:0379-6717-1711

Home page >> Information Center >>Product description >> 9100 FDA EUA Instruction-EN149
Details

9100 FDA EUA Instruction-EN149

FDA EUA Instruction - EN 149:2001+A1:2009

Electronic Labeling

Release Time: 2020-8-5 9:05:58

User Instructions

FFP2 NR 9100 Non-medical Filtering Half Mask

Warnings and Limitations

Failure to follow all instructions and limitations on the use of these respirators and/or failure to wear these respirators during all times of exposure can reduce effectiveness and may result in sickness or death. For additional information please contact us at www.bing-zun.com or call + 8637967171711

Intended Use

These particulate respirators are designed to protect against solid and non-volatile liquid particles.

Use Instructions

1. These respirators meet the requirements of EN 149:2001 +A1:2009, filtering face piece respirators for use against particles. They should be used to protect the wearer from solid and non-volatile liquid particles only.

2.                  Proper selection, training, use and appropriate maintenance are essential for the respirator in order to protect the wearer from certain airborne contaminants. Failure to follow all instructions on the use of these respiratory protection and/or failure to properly wear the complete respirator during all periods of exposure may adversely affect the wearer' s health, easily leading to severe or life threatening ilness or permanent disability.

3. Always check and make sure that the respirator is within the stated shelf life (use by date).

4. Before use, the wearer must be trained in use of the complete respirator in accordance with Health and Safety standards/guidance.

5. These respirators do not contain components made from natural rubber latex.

6. These respirators do not protect against gases/vapors.

7. Not to be used on children.

8. Do not use in atmospheres containing less than 19.5% oxygen.

9. Do not use for respiratory protection against atmospheric contaminants / concentrations which are unknown or immediately dangerous to life and health (IDLH).

10. Do not use with beards or other facial hair, which might inhibit contact between the face and the respirator, thus preventing a good seal.

11. Leave the contaminated area immediately if:

a) Breathing becomes difficult.

b) Dizziness or other distress occurs.

12. Always be sure you are using the complete respirator.

13. The respirator is suitable for application.

14. The respirator is worn during all periods of exposure.

15. Replace respirator when necessary.

16. Discard and replace the respirator if it becomes damaged, breathing resistance becomes excessive or at the end of the shift.

Fit Check

1. Cover the front of the respirator with both hands being careful not to disturb the fit of the respirator.

2. For UNVALVED respirator - EXHALE sharply.

3. For VALVED respirator - INHALE sharply.

4. If air leaks around the nose, re-adjust the nose clip to eliminate leakage. Repeat the above fit check.

5. If air leaks at the respirator edges, work the strap bank along the sides of the head to eliminate leakage. Repeat the above fit check. If you CANNOT achieve a proper fit, DO NOT enter the hazardous area.

微信截图_20200912171806.png

Fitting Instructions

All respirator components should be inspected for damage prior to each use.

1. Cup respirator in one hand with nose piece at fingertips, allow headbands to hang freely below the hand.

2. Hold respirator under chin, with nose piece up.

3. Locate the upper strap across the crown of the head and the lower strap below the ears.

4. Straps must not be twisted.

5. Using both hands, mold nose-clip to the shape of the lower part of the nose to ensure a close fit and good seal. Pinching the nose-clip using only one hand may result in less effective respirator performance.

6. The seal of the respirator on the face should be fit-checked before entering the workplace.

1212.png

Cleaning Instructions

1. Do not alter, modify, clean or repair this respirator.

2. Dispose in accordance with local regulations.

Storage and Transportation

1. Store in accordance with manufacturer' s instructions.

2. Storage temperature should be between -30°C and +70 °C.

3. Storage humidity should be less than 80%.

4. When storing or transporting this respirator use original packaging provided.

5. Do not store in direct sunlight.

Classification

There are three equipment classes: FFP1/FFP2/FFP3 (See marking on box and on mask). For the particle filtering half mask marked "NR” , it shall not be used for more than one shift.

Approvals

These respirators are tested by SGS institution, and audited annually by SGS Fimko Oy    Notified Body  No. 0598 .

These respirators are CE Marked in accordance with the requirements of European Regulation (EU) 2016/425. The applicable legislation can be determined by reviewing the Certificate and Declaration of Conformity at www.bing-zun.com.

Notified Body

SGS Fimko Oy    Notified Body  No. 0598

Address: Takomotie 8, FI-00380 Helsinki, Finland


Homepage   |  About bingzun   |  Product display   |  Information Center   |  contact us

Service hotline:0379-6717-1711   mailbox:sales@bing-zun.com

Address: 50m next to the south of Guihua mountain villa, Xin'an industrial cluster, Luoyang City, Henan Province

Telephone
Feedback
E-MAIL
Contact Us:
0379-6717-1711
No content
Word 500(limit 500 Character)